British Columbia · Tank, tankless and heat pump · Updated November 2026
Water heater installation, explained.
What to install, what it costs, which permits and rebates apply in B.C., and what a proper installation looks like.
By Andrew HendersonRed Seal Plumber
Tank leaking right now?
1. Close the cold water valve on the pipe above the heater.
2. Turn the gas control to off, or switch off the breaker for an electric tank.
3. Smell gas? Leave the house, then call FortisBC at 1-800-663-9911. More on leaks
- 10 to 13 yearsTypical life of a gas storage tank, according to FortisBC
- 19.3%Share of a Canadian home's energy that goes to heating water
- $1,000CleanBC rebate for a qualifying heat pump water heater
- January 1, 2027Vancouver's replacement rule starts for houses and duplexes
Start here
The three types.
Every residential water heater is one of these. The right one depends on your fuel, your space and how long you plan to stay.
-
Lowest cost to install
Storage tank
Heats a tank of water with a gas burner or electric elements and keeps it hot until you need it.
- Lasts
- 10 to 13 years (gas)
- Good for
- A straight swap, a tight budget, a house you may sell
- Watch for
- It can run out, and it uses energy keeping water hot all day
-
Longest life
Tankless
Heats water only as it flows through, so it does not run out. Hangs on a wall.
- Lasts
- About 20 years
- Good for
- Big households, small mechanical rooms, long-term owners
- Watch for
- Often needs a bigger gas line and new venting, plus a yearly flush
-
Lowest energy use
Heat pump
An electric tank that moves heat from the surrounding air into the water instead of making heat directly.
- Lasts
- About 13 years
- Good for
- Electric homes, rebates, meeting Vancouver's 2027 rule
- Watch for
- Needs air space and a condensate drain, and it cools the room it sits in
Typical pricing, not an estimate for your home
What it costs.
| Job | Typical price | Where the number comes from |
|---|---|---|
| Storage tank, installedReplacing a tank with a tank | $2,489 to $3,589+ | Unclog.it price guide, Metro Vancouver and the Fraser Valley |
| Electric tank replacing gas | $2,650 average | City of Vancouver pilot with BC Hydro, before rebates |
| Heat pump water heater | $4,240 average | Same pilot. None of the ten homes went over $5,000 before rebates |
| Tankless | Estimated on site | The gas line, venting and drain work varies too much to give one range |
| Repair instead | $429 to $959+ | Unclog.it price guide |
The heater itself is often less than half the bill. The rest is the labour and parts that make the installation safe and legal: venting, gas, seismic straps, thermal expansion, permits and hauling the old tank away.
What you are paying for
A proper installation.
Two installations of the same tank can look alike from across the room and be very different. These are the parts an inspector, and a careful plumber, look for.
- Cold water shut-off. A working valve on the supply so the heater can be isolated in seconds. Old seized valves get replaced with the tank.
- Thermal expansion tank. Heated water expands. Where the supply has a check valve, backflow preventer or pressure-reducing valve, the BC Plumbing Code requires somewhere for that pressure to go.
- Mixing valve. Lets the tank store water at 60°C, hot enough to control bacteria, while sending cooler water to the taps.
- Seismic straps. The tank is braced to the building so it cannot topple and tear its gas and water lines in an earthquake.
- Relief valve and discharge pipe. The temperature and pressure relief valve is the last line of defence against an overheated tank. Its pipe runs down toward the floor and is never capped or plugged.
- Gas shut-off and dirt pocket. The heater gets its own gas valve, and a short capped drop that catches debris before it reaches the gas control.
- Drain pan. Where a leak would damage finished space, the tank sits in a pan that is piped to a drain.
- Drain valve. For flushing sediment once a year and for emptying the tank at the end of its life.
- Venting. Sized and sloped for this heater, then tested for draft. A new heater on an old, oversized chimney is a common cause of spillage.
The drawing shows a typical gas storage tank. What your home needs depends on the heater, the house and your local inspector.
Two to four hours for a straight swap
Installation day.
- Look first. Fuel, venting, tank size, the gas line and what has to come up to current code. You get a written estimate before anything is disconnected.
- Permits. The contractor takes out the gas, plumbing or electrical permits the job needs.
- Out with the old. Water and gas or power off, tank drained, disconnected and carried out.
- Set and connect. New heater in place, strapped, and connected to water, then gas and venting or wiring.
- Fill, then fire. The tank is filled and the air is bled out at a hot tap before the burner is lit or the breaker goes on. Powering an empty electric tank burns out its elements.
- Test. Gas joints are leak tested, the vent is checked for draft, the relief valve and temperature are checked.
- Walk-through. You are shown the shut-offs and the temperature setting, and you get the permit details and warranty paperwork.
Regulated work
Permits.
Gas and electrical work in B.C. is regulated under the Safety Standards Act. A licensed contractor takes out the permit for you. A change from a tank to a tankless heater, or a change in how the heater is vented, needs a full gas installation permit.
Checked November 2026
Rebates.
A qualifying heat pump water heater earns $1,000 through CleanBC Better Homes, and up to $3,500 for income-qualified households. Broken-tank emergency replacements are often not eligible, so plan ahead.
City of Vancouver
From January 1, 2027, a replacement water heater in a house or duplex has to be at least 100% efficient.
That means electric or heat pump. A like-for-like gas tank or gas tankless replacement will no longer comply. What the rule covers and who is exempt.
Before it fails
Time to replace?
- The tank is more than 10 years old
- Water on the floor around the base
- Rusty or cloudy hot water
- Rumbling, popping or banging as it heats
- Hot water runs out sooner than it used to
- The relief valve keeps dripping
Not all of these mean a new heater. Several are repairs. A tank that is leaking from its own shell is finished, and it is the one case that cannot wait.
Replacing a tired heater on your schedule keeps your rebate options open and avoids an after-hours emergency.
Short answers
Questions.
How long does a water heater installation take?
Replacing a tank with the same kind of tank typically takes two to four hours, and you have hot water again within an hour or so of the heater being lit or switched on. Switching to a tankless or heat pump water heater typically takes most of a day, because the gas line, venting, wiring or drain usually has to change.
Can I install a water heater myself in B.C.?
Sometimes, with a permit. Technical Safety BC lists replacing a water heater as gas work a homeowner can do under a homeowner gas permit, but only in a detached house that you own and live in. A house with a suite, a duplex, a townhouse or a condo needs a licensed contractor. The work is inspected either way. Who is allowed to do the work.
How long does a water heater last?
FortisBC puts a gas storage tank at 10 to 13 years, a condensing storage tank at 12 to 15, a heat pump water heater at about 13 and a tankless water heater at about 20. Hard use, sediment and a missing expansion tank all shorten that. Repair or replace.
What temperature should a water heater be set to?
Store it at 60°C. That is hot enough to control Legionella bacteria in the tank, and it is the minimum storage temperature in Vancouver's plumbing by-law. Water that hot scalds quickly, so a mixing valve at the heater, or temperature-limiting valves at the fixtures, bring it down before it reaches a tap.
Do I need an expansion tank?
If your water supply has a check valve, a backflow preventer or a pressure-reducing valve, yes. The BC Plumbing Code requires protection against thermal expansion in those cases, because heated water has nowhere to expand to. A relief valve that drips after every heating cycle is the usual sign one is missing.
Is a tankless water heater worth it?
It suits a home that runs out of hot water, is short on floor space, and plans to stay put long enough to use its roughly 20-year life. It costs more to install than a tank, usually because the gas line and venting have to be upgraded, and it needs a yearly flush. Compare the three types.
What happens to the old tank?
It is drained, disconnected and hauled away for metal recycling. Check that removal and disposal are written into your estimate.
Sources
- FortisBC: Tank or tankless? How to find your perfect match in a water heater
- Natural Resources Canada: Guide to residential water heaters
- City of Vancouver: Hot water at home, time-of-replacement questions and answers (PDF)
- CleanBC Better Homes: Electric heat pump water heater rebate
- Technical Safety BC: Making gas or electrical changes to your home
- BC Plumbing Code 2018, Division B, Section 2.6 (thermal expansion, service water heaters)
- City of Vancouver: Building By-law plumbing summary (hot water storage temperature) (PDF)
- Unclog.it price guide: Water heater installation
More water heater help
Legal disclaimer
The information on this site is provided for general educational purposes only and does not constitute professional advice. Gas, electrical and plumbing work can cause property damage, injury or death if performed incorrectly, and is regulated in British Columbia. Always follow the manufacturer's instructions, the applicable codes and the terms of your permit. If you are unsure at any time, stop and contact a licensed contractor.
Prices shown are typical figures, not an estimate for your home. Rebate amounts and rules are set by the programs named and can change without notice. Pure Mechanical Group Ltd. makes no warranties or guarantees and expressly disclaims liability for any loss, damage, or injury arising from the use of this content. By using this site you agree to these terms.